FlashTrack FT-15 Quickstart guide
FlashTrack FT-15
DSP Microphone — setup, controls, and connections.
Click on the section you want to read more about.
Anatomy & Controls
FlashTrack has fourteen control points and ports. The microphone head and the Bluetooth button also indicate the current status by colour.
FT_USB
FT_BT
No light · Standby
Flashing · Pairing
Steady · Paired
Usage Steps
Connect, monitor, then configure your software. Watch the microphone head colour — a purple light means you're ready to record.
- Connect the USB devicePlug FlashTrack into your computer or phone with the original cable. The green light turns on and the opening animation plays.
- Connect headphonesPlug headphones into the monitor jack and use the VOL button to set microphone and monitor levels.
- Configure your softwareSelect FlashTrack in your recording software. A purple light confirms a successful connection — you're ready to record.
Connections
FlashTrack routes computers, phones, instruments and Bluetooth audio through a single body. Choose the input that matches your setup.
FlashTrack's USB-C interface connects to a computer or smartphone. It powers FlashTrack over USB-C and also functions as a USB audio interface.
A USB 5V input that serves as a backup power source when a smartphone's OTG supply over USB-C is insufficient. Using this port also reduces FlashTrack's power draw from the phone during recording.
FlashTrack supports Bluetooth audio input. Device name: FT_BT
| Action | Result |
|---|---|
| Short press / hold 3 s | Enter pairing mode (light flashing). |
| Hold 10 s | Forget paired devices (reset to discoverable state). |
Keyboard: use a 6.3 mm to 3.5 mm stereo cable to connect to the AUX IN.
Guitar: if your guitar has a built-in pickup preamp, use a 6.3 mm to 3.5 mm signal cable to connect the guitar's output to the AUX IN.
Specifications
Dimensions exclude the microphone stand. Tolerances ±1%.
| Microphone Type | Condenser Microphone |
| Max SPL | 130 dB |
| Capsule Size | Ø25 mm |
| Polar Pattern | Cardioid |
| Frequency Response | 20 Hz ~ 20 kHz |
| Gain Range | Up to 46 dB |
| Bit Depth | 24 bit |
| Sample Rate | Up to 192 kHz |
| Headphone Output | 3.5 mm TRS |
| Analog Input | 3.5 mm TRS |
| Wireless Input | Bluetooth 5.0 |
| Digital Interface | USB-C (USB 2.0) |
| Power | 5V DC |
| Dimensions | 65 (L) × 64 (W) × 108 (H) mm |
| Net Weight | 270 g |
FCC Compliance
Federal Communication Commission Interference Statement.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example — use only shielded interface cables when connecting to computer or peripheral devices).
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Support
For tutorials, FAQs, warranty terms and product registration, visit our official website. This space is also reserved for future interactive content.